64 C10, throwing out the feelers.

« Prev
1
Next »

zor New Member Posts: 45	64 C10, throwing out the feelers. Mar 8, 2010 13:59:14 GMT -7 Quote Select Post Deselect Post Link to Post Member Give Gift Back to Top Post by zor on Mar 8, 2010 13:59:14 GMT -7 SOLD
	Last Edit: Apr 29, 2010 16:29:48 GMT -7 by zor Load sixteen tons and what do ya get, Another day older and deeper in debt.

Dave Young Administrator If at first you don't succeed, change your definition of success. Posts: 427	64 C10, throwing out the feelers. Mar 10, 2010 0:17:31 GMT -7 Quote Select Post Deselect Post Link to Post Member Give Gift Back to Top Post by Dave Young on Mar 10, 2010 0:17:31 GMT -7 Short or long bed? Small or large rear window? Custom or standard trim? Engine? 10 or 12 bolt rear end? Ratio? Posi? Condition of body panels/glass? Etc... etc... etc...
	Dave Young San Tan Valley, AZ 1964 Chevy C-10

zor
New Member

Posts: 45

64 C10, throwing out the feelers. Mar 10, 2010 21:19:34 GMT -7

Quote

Post by zor on Mar 10, 2010 21:19:34 GMT -7

Long bed.
small winder,
no trim,
230 that runs,
Needs typical patch panels, I'm taking the windshield out for my new project, all other glass is there and I think I have an extra hood for it and if you want a three speed trans. Oh and it has 4.11's with five lug axles and five lug discs up front. I think it's a 10 bolt, haven't really looked and I usually run 9" fords so I'm not really familiar with gm rears. I don't know if it's posi (with a 230 I've never really been able to test it

)
and I have the B pillar trim with "custom" scripted on the bottoms. and an extra driver's fender that's good for patching the existing fender.

Last Edit: Mar 10, 2010 21:23:25 GMT -7 by zor

Load sixteen tons and what do ya get, Another day older and deeper in debt.

zor New Member Posts: 45	64 C10, throwing out the feelers. Apr 15, 2010 18:19:02 GMT -7 Quote Select Post Deselect Post Link to Post Member Give Gift Back to Top Post by zor on Apr 15, 2010 18:19:02 GMT -7 Alright, this sucker has to go. Let me know if you want pictures, I'll email them to you. Zor
	Load sixteen tons and what do ya get, Another day older and deeper in debt.

Quick Reply

Shoutbox

sunshinechevy66: Hello

anyone know if its possible to turn my c10 into 4x4 ? Aug 30, 2014 17:43:41 GMT -7

jakerc20: does anyone know where i can get a rolling frame for a 64 c10 in tucson az Sept 9, 2014 11:04:39 GMT -7

builder: Any one know if Toyota 6 lug late model truck, 4runner or fj cruiser rims will fit on a stock 64-65 or 66 chevy c10 wheel? the bolt pattern seems the same, the center hole is my unknown. i am talking about some stock take off 17 inch Toyota truck rims. Dec 6, 2014 19:58:50 GMT -7

builder: pantano and golf links a dude is parting out oneyou will see it in his front yard between golflinks and escalante. for you jaker20 im restoring a66 in tucson. Dec 6, 2014 20:02:29 GMT -7

partridge1962: I'm new here and trying to figure out my way around. I have a 1962 C10 long bed with a 355 engine with original rear end. I want to change the rearend to something very low around 3:08----ANY SUGGESTIONS FOR ME? Mar 28, 2015 6:51:03 GMT -7

partridge1962: well 3:08 is very high not low my fault Mar 28, 2015 6:51:54 GMT -7

marcusarobins: Antone have any 60-66 front fenders that arent rusted? May 26, 2015 20:42:10 GMT -7

Dave Young: If you haven't already, check out the Facebook group page. It has nearly 10 times the amount of members and is easier to follow up with. It's a great group with very helpful members. I highly recommend it. Feb 24, 2016 11:21:28 GMT -7

Dave Young: www.facebook.com/groups/6066chevytrucks/ Feb 24, 2016 11:22:01 GMT -7

crabman19: that would be great Dave if I was on Facebook, but I'm not..... Mar 25, 2016 17:29:11 GMT -7

blackdog: Wondering if anyone has replaced the Munci SM40 4 speed manual with a more modern manual tranny that had overdrive? I plan to install a 5.3L into my 1966 C20 and was wondering if I should do a tranny upgrade at the same time. What makes sense - Thanks Dec 16, 2016 6:47:56 GMT -7

treyweb26: New to the forum and beginning a resto on a 66 C10 Fleetside. Excited about the challenge and eager to get to work on it. Advice is appreciated as to whether do I rebuild the orginal 283 or drop a 350 crate, switching to 5-lug and keeping it a long bed. Jun 4, 2017 21:35:59 GMT -7

jrsr: Does anyone know the best and most economical way change a 196666 Chevy C20 to a 5 or 6 lug wheel to lower the stance. I was looking for a C10, But ran into a great deal on a 1966 C20 with low miles Nov 7, 2017 14:14:23 GMT -7

jrsr: Or , Is it easier and better to change to rear end and the engine cradle to get the new supension Nov 7, 2017 14:15:54 GMT -7

mrisinge: Just joined. 1966 SWB, chopped 4", 454, Turbo 400, basket case. 1990 front clip, Ford 9". Will need lots of advice and tech assistance to get this bad boy back on the road. Looking forward to make this happen. Nov 30, 2017 5:44:41 GMT -7

mrisinge: Has this Forum died? Questions never get answered. Am I missing something? Jul 28, 2018 5:02:20 GMT -7

carlena: This is my first time here... Trying to post... I'm looking for some 1965 C10 Step side Truck Doors... Oct 29, 2018 10:18:16 GMT -7

cdandelivery: 60 custom cab rear axle leak.who has dealt with this? Jul 18, 2019 7:20:43 GMT -7

mahto: hi thanks for the add an I have a 64 C10 that was parked at San Diego Navel base and has roof rusted what is best to do get a new cab or weld new top on thanks Feb 21, 2020 10:15:36 GMT -7

softballman: NEED HELP TO REMOVE GAUGE CLUSTER OF 66 C10 DASH Jan 11, 2024 6:58:32 GMT -7

64 C10, throwing out the feelers.

Post by zor on Mar 8, 2010 13:59:14 GMT -7

Post by Dave Young on Mar 10, 2010 0:17:31 GMT -7

Post by zor on Mar 10, 2010 21:19:34 GMT -7

Post by zor on Apr 15, 2010 18:19:02 GMT -7

Quick Reply

Shoutbox