Buff Block

new

« Prev
1
Next »

jason
New Member

Posts: 3

Buff Block Jan 27, 2010 9:38:46 GMT -7

Quote

Post by jason on Jan 27, 2010 9:38:46 GMT -7

There are a few things on my truck that simply were ugly and i wanted to clean them up a bit.I saw that my gf had a nail buffer and what it is is a rectangle block that has 5 stages. It starts at 2500 grit and gets very very very fine as you go through them.I used it on my ignition and what once looked like a dull peice of alluminum now looks like chrome.Not only that it took the scratches out of it that the key made. I used it on my tail lights and with some cuting of the block and in 10 min they look almost new. The block only sets you back 5 bucks and i find it a real good investment.After yor done blocking your part just use some polish/protector and you will get long lasting good looks.

Dave Young Administrator If at first you don't succeed, change your definition of success. Posts: 427	Buff Block Jan 28, 2010 1:23:53 GMT -7 Quote Select Post Deselect Post Link to Post Member Give Gift Back to Top Post by Dave Young on Jan 28, 2010 1:23:53 GMT -7 I've heard of that before. Thanks for posting.
	Dave Young San Tan Valley, AZ 1964 Chevy C-10

Quick Reply

Shoutbox

sunshinechevy66: Hello

anyone know if its possible to turn my c10 into 4x4 ? Aug 30, 2014 17:43:41 GMT -7

jakerc20: does anyone know where i can get a rolling frame for a 64 c10 in tucson az Sept 9, 2014 11:04:39 GMT -7

builder: Any one know if Toyota 6 lug late model truck, 4runner or fj cruiser rims will fit on a stock 64-65 or 66 chevy c10 wheel? the bolt pattern seems the same, the center hole is my unknown. i am talking about some stock take off 17 inch Toyota truck rims. Dec 6, 2014 19:58:50 GMT -7

builder: pantano and golf links a dude is parting out oneyou will see it in his front yard between golflinks and escalante. for you jaker20 im restoring a66 in tucson. Dec 6, 2014 20:02:29 GMT -7

partridge1962: I'm new here and trying to figure out my way around. I have a 1962 C10 long bed with a 355 engine with original rear end. I want to change the rearend to something very low around 3:08----ANY SUGGESTIONS FOR ME? Mar 28, 2015 6:51:03 GMT -7

partridge1962: well 3:08 is very high not low my fault Mar 28, 2015 6:51:54 GMT -7

marcusarobins: Antone have any 60-66 front fenders that arent rusted? May 26, 2015 20:42:10 GMT -7

Dave Young: If you haven't already, check out the Facebook group page. It has nearly 10 times the amount of members and is easier to follow up with. It's a great group with very helpful members. I highly recommend it. Feb 24, 2016 11:21:28 GMT -7

Dave Young: www.facebook.com/groups/6066chevytrucks/ Feb 24, 2016 11:22:01 GMT -7

crabman19: that would be great Dave if I was on Facebook, but I'm not..... Mar 25, 2016 17:29:11 GMT -7

blackdog: Wondering if anyone has replaced the Munci SM40 4 speed manual with a more modern manual tranny that had overdrive? I plan to install a 5.3L into my 1966 C20 and was wondering if I should do a tranny upgrade at the same time. What makes sense - Thanks Dec 16, 2016 6:47:56 GMT -7

treyweb26: New to the forum and beginning a resto on a 66 C10 Fleetside. Excited about the challenge and eager to get to work on it. Advice is appreciated as to whether do I rebuild the orginal 283 or drop a 350 crate, switching to 5-lug and keeping it a long bed. Jun 4, 2017 21:35:59 GMT -7

jrsr: Does anyone know the best and most economical way change a 196666 Chevy C20 to a 5 or 6 lug wheel to lower the stance. I was looking for a C10, But ran into a great deal on a 1966 C20 with low miles Nov 7, 2017 14:14:23 GMT -7

jrsr: Or , Is it easier and better to change to rear end and the engine cradle to get the new supension Nov 7, 2017 14:15:54 GMT -7

mrisinge: Just joined. 1966 SWB, chopped 4", 454, Turbo 400, basket case. 1990 front clip, Ford 9". Will need lots of advice and tech assistance to get this bad boy back on the road. Looking forward to make this happen. Nov 30, 2017 5:44:41 GMT -7

mrisinge: Has this Forum died? Questions never get answered. Am I missing something? Jul 28, 2018 5:02:20 GMT -7

carlena: This is my first time here... Trying to post... I'm looking for some 1965 C10 Step side Truck Doors... Oct 29, 2018 10:18:16 GMT -7

cdandelivery: 60 custom cab rear axle leak.who has dealt with this? Jul 18, 2019 7:20:43 GMT -7

mahto: hi thanks for the add an I have a 64 C10 that was parked at San Diego Navel base and has roof rusted what is best to do get a new cab or weld new top on thanks Feb 21, 2020 10:15:36 GMT -7

softballman: NEED HELP TO REMOVE GAUGE CLUSTER OF 66 C10 DASH Jan 11, 2024 6:58:32 GMT -7

Buff Block

Post by jason on Jan 27, 2010 9:38:46 GMT -7

Post by Dave Young on Jan 28, 2010 1:23:53 GMT -7

Quick Reply

Shoutbox